CX-3 2WD

490 service bulletins filed with NHTSA for this model year

• May 1, 2026POWER TRAIN01-008-26

  This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 01-008/23 06/05/23 Some vehicles may exhibit rattling noises from the engine compartment and oil leakage from the drive belt auto tensioner. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner

• Apr 30, 2026UNKNOWN OR OTHERSA-031-26

  DESCRIPTION Some vehicles may require the replacement of a damaged VIN plate or vehicle certification label. To obtain a replacement VIN plate (bulkhead-mounted and visible through the lower-left area of the windshield), contact DAG (Dealer Assistance Group) using VIN Plate Request Form available on One Mazda. To obtain a replacement vehicle certification label (located on the B􀀀pillar or front door), contact your assigned DSM (District Service Manager) to place the order. If DSM contact informa

• Apr 21, 2026POWER TRAINSA-029-26

  This Service Alert supersedes the previously issued SA listed below: The changes are noted in Red. SA-011/24 02/12/24, 06/06/24, 07/29/24 DESCRIPTION Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services ar

• Apr 16, 2026ENGINESA-026-26

  This Service Alert supersedes the previously issued M-Tip(s) listed below. The changes are noted in Red text. MT-002/19 09/30/19 and 12/19/19 DESCRIPTION If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure)

• Apr 11, 2026FUEL/PROPULSION SYSTEMSA-023-26

  This Service Alert supersedes the previously issued M-Tip(s) listed below. The changes are noted in Red text. MT-003/22 03/02/22 DESCRIPTION Some customers may complain about a tapping or knocking noise coming from the rear seat after fuel fill. The concern will likely occur if the fuel tank is overfilled (more fuel is added after the fuel pump nozzle shuts off automatically) or filled up normally in high ambient temperatures and the fuel expands. No repair is needed. Explain to the customer not

• Apr 4, 2026ELECTRICAL SYSTEMSA-021-26

  This Service Alert supersedes the previously issued SAs and bulletin(s) listed below: The changes are noted below in red. SA-010/23 02/09/23 DESCRIPTION Some customers may experience one or more electrical malfunctions after a vehicle body repair. A newly painted fender stay (2) may be causing a poor front harness (1) ground connection. The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. NOTE

• Jan 26, 2026UNKNOWN OR OTHERSA-005-26

  There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method • B. Auxiliary Key Code Cut Method 2019 and newer models require a 10-digit key code to accurately cut keys • 5-digit codes CANNOT be provided for 2019 and newer vehicles (the traditional 5-digit code from the key tag or driver's door lock cylinder is not sufficient and will not be issued for key cutting on these models). • Only Mazda-approved key cutting machines can process these 10-digit cod

• Jan 13, 2026ELECTRICAL SYSTEM09-005-26

  If the right-side Blind Spot Monitoring (BSM) control module is replaced for any reason, it is also necessary to replace the left-side BSM control module in order to complete the radar aiming procedure. If the right-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" cannot be completed due to a programming error in the module. In most cases, if the left-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" can be comp

• and 482 more

Source: NHTSA manufacturer communications (technical service bulletins).