Rogue FWD SL/Platinum

14 service bulletins filed with NHTSA for this model year

• May 1, 2026FUEL/PROPULSION SYSTEMNTB26-006A

  FUEL FILLER TUBE LOWER SEAL IS LEAKING AND DTC P0456 IS STORED IN THE ECM This bulletin is no longer active. Please discard previous versions of NTB26-006.

• Apr 15, 2026ENGINENTB26-019

  MIL ON WITH DTC P0181 STORED IN THE ECM IF YOU CONFIRM The customer states the MIL is ON but the vehicle does not have any drivability concerns or reduced power message in the combination meter, AND DTC P0181 for “Fuel Tank Temperature” is stored in either “Past” or “Current” in the ECM. ACTION Follow the SERVICE PROCEDURE in this bulletin to: 1. Replace the fuel temperature sensor. 2. Erase all the DTCs.

• Apr 13, 2026STRUCTURE:BODYNTB09-131C

  CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is a

• Feb 2, 2026FUEL/PROPULSION SYSTEMNTB26-006

  FUEL FILLER TUBE LOWER SEAL IS LEAKING AND DTC P0456 IS STORED IN THE ECM IF YOU CONFIRM The vehicle has a visible leak with a smoke machine test coming from the fuel filler tube lower seal, AND DTC P0456 is stored as “Active”, “Past”, or “Pending” in the ECM. ACTION 1. Remove the supplied funnel from the rear of the vehicle or trunk. 2. Insert the funnel completely in the fuel filler tube and remove completely five (5) times. 3. Re-check the fuel filler tube lower seal with a smoke machine to d

• Jan 7, 2026ENGINENTB25-063

  VENT CONTROL VALVE IN ACTIVE TEST INOPERATIVE IN CONSULT 4 SERVICE INFORMATION An issue in CONSULT 4 has been identified in “EVAP system close” in Work support. · After selecting the "EVAP system close" in Work support, the “VENT CONTROL/V” in Active test becomes non-functional temporarily. · When selecting “EVAP system close” operation in Work support, wait 10 minutes before starting “VENT CONTROL/V” Active test or cycle the IGN switch ON/OFF for “VENT CONTROL/V” Active test to be operational.

• Dec 15, 2025ENGINENTB25-064

  MIL ON WITH DTCS P05D8 AND P05D9 STORED IN THE ECM IF YOU CONFIRM The MIL is ON with DTCs P05D8 for “PCV Regulator Valve Control Circuit/Open” and P05D9 for “PCV Regulator Valve Control Circuit Low” stored in the ECM, AND The wiring harness, for wiring harness connector F130, is severed at the Crank Case Ventilation Valve under the Engine Cover. ACTION Follow the SERVICE PROCEDURE starting on page 3 to repair the wiring harness. IMPORTANT: The purpose of ACTION (above) is to give you a quick ide

• Oct 14, 2025ELECTRICAL SYSTEMNTB25-046

  VOLUNTARY SERVICE CAMPAIGN 2025 ROGUE; REMOTE ENGINE START BCM CONFIGURATION INTRODUCTION Nissan is conducting this voluntary service campaign on certain specific model year 2025 Rogue vehicles to reconfigure the BCM. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PD175 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RE

• Oct 1, 2025ELECTRICAL SYSTEMNTB25-030A

  STEERING WHEEL SWITCH BUTTONS INOPERATIVE, STICKING, OR NOT CLICKING WHEN PRESSED IF YOU CONFIRM The customer states that any of the steering wheel switch buttons are inoperative, sticking, or not clicking when pressed. ACTION Follow the SERVICE PROCEDURE to: 1. Remove the steering wheel assembly. 2. Replace the switch assembly on the steering wheel assembly. HINT: The switch assembly includes switches for both sides of the steering wheel. 3. Reinstall the steering wheel assembly. IMPORTANT: The

• and 6 more

Source: NHTSA manufacturer communications (technical service bulletins).