AMG GLE63 S 4matic Plus

176 service bulletins filed with NHTSA for this model year

• May 29, 2026ELECTRICAL SYSTEMLI00.20-P-077615

  Complaint 1. "Perform vehicle handover" in the workshop menu to start the maintenance computer for service A/B cannot be carried out. 2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head u

• May 26, 2026ELECTRICAL SYSTEMLI82.85-P-080507

  Complaint After successful commissioning of the HERMES control unit (N112/9) with XENTRY Diagnosis DVD 03/2026, the message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: • HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) • Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Caus

• May 22, 2026STRUCTURE:BODYPSL-NCU Return Parts 5/22

  Dear Mercedes-Benz USA Dealers, The part numbers listed in the chart below should no longer be installed, and any existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, June 11, 2026. After June 11th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This p

• May 22, 2026STEERINGLI46.15-P-070510

  Complaint Noises from the area of the steering column. - Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. • Instrument panel support • Steering column switch module NOTE: Occasionally to verify complaint, the steering column/vehicle needs to be in direct sunlight or hot conditions for a few hours. If noise only occurs when adjusting the ste

• May 19, 2026POWER TRAINLI27.00-P-080462

  Complaint Harsh upshifts, downshifts, or jolting in lower gears when accelerating. Cause Incorrectly installed (rotated) rotational speed sensors on the EHS (VGS Control Unit) can cause abnormalities in signals. As a result, poor adaptation values are stored and harsh gearshifts are felt. This only affects vehicles with VGS control units produced between days 185-296 of 2025 (July 4, 2025-October 23, 2025). Remedy 1. Collect initial transmission EEPROM file 2. Check EEPROM .txt file for VGS cont

• May 18, 2026ENGINELI07.10-P-080384

  Complaint Customer reports Check Engine Light with possible loss of power concern. The Following DTC's are present • P210185 - The throttle valve actuator has a malfunction. There is a signal above the permissible limit value. • P213500 - The values from the position sensors of the throttle valve are implausible relative to each other • P213600 - The values from position sensors "A/C" of the throttle valve are implausible relative to each other • P210B85 - The throttle valve actuator 2 has a mal

• May 15, 2026VISIBILITY/WIPERLI82.30-P-078932

  Complaint Approx. A 5–10 cm wide unwiped strip remains in the area of the wiper blade attachment during the downward movement of the wiper on the driver's side or front passenger side (see Figure 1). Cause During replacement of worn wiper blades, the wrong blades were installed, contrary to the specifications. Left-hand drive vehicle: Incorrect: A1678209201 Correct: A1678208703 The standard wiper system from model series 167 was changed in October 2022. The wiper arms of the standard system afte

• May 15, 2026SERVICE BRAKESLI42.10-P-078779

  Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. Vehicle production date prior to December 2025. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtighte

• and 168 more

Source: NHTSA manufacturer communications (technical service bulletins).